I'm in NorCal and would love to sell to a racer who wants everything in one lot. I've raced 944s for 15+ years and have just about everything. Take a look at the list and see pictures here: goo.gl/photos/8rk2qPodCiczmoQA6

If you let me know what you want and if you need it shipped, I'll respond with a price. I'm looking to get some cash out of this stuff but will be reasonable with everything. The more you buy the better!

My email is 94472SL AT GMAIL DOT COM

In addition to the pictures, I still have a garage full of stuff I'll be inventorying in the next few weeks but I'll post that list at the bottom of the stuff I know.

Pictured Stuff: (lined out is sold)

Low compression pistons with rods (some light marks, one scratch, see pictures)
Several ECUs (one early, several late, some have aftermarket chips, see pics)
Shifter
Fuel level sender
Crank position sensors
Air Flow meter (tested/known good, never opened)
Fuel rail with injectors
Gas cap
Lindsey racing brake ducts for front rotors (the piece that bolts to the spindle)
Box of relays and fuses
Front wheel bearing set with grease seals NEW
Ball Joints X 2 NEW
Oil Filters Mahle X 3 NEW
Eibach 400 LB front springs with helper springs
Racer's Edge Camber Plates
Ground Control adjustable coil over spring perches
Koni Yellow front with some strut caps and bump stops thrown in
K&N Air Filter NEW
CV Axle Boot Kits X 2 NEW
Front Brake Rotors X 2 NEW
Engine wiring harness for parts (I had some custom connections on it for my setup)
AFM boot
Mahle Air Filter NEW
Throttle body (I believe this is one that someone modified by boring/smoothing, came from a parts car)
Crank Position sensors with bracket
Throttle Cam aftermarket
Misc Gaskets, pedal covers, etc (see pic)
Misc used ignition parts (see pic)
Throttle Cable
Fuel Injectors (P/N 280.150.158) X 9 with spare seals etc (all used, condition unknown)
Another set of relays

Not pictured:

Airflow meters X 3 (condition unknown)
Alternator adjustment rod X 2
Bumper Shock
Brake Calipers (all 4, recently rebuilt)
Control Arms Steel X 2 (New)
Hubs Rear X 5 (early offset)
Intake manifold X 2
Side mirror
Radiator
Rear Axle Nuts (New I think)
Shifters X 2 (part that bolts to torque tube)
Slave cylinder
Spindles left and right early offset
Eibach 450 LB springs
Starter
Stock steering wheel (rough but good spare just in case)
Stub axles rear X 5
Tie Rods X 4 (I think I have both power and manual rack tie rods)
Timing belt covers
Trailing arms aluminum (I have 3 or 4, some have new wheel bearings already in)
Transmissions X 2 (both late cases, open diff, normal 5th)
Trans couplers, several
Water neck
Wiper assembly with motor etc
Turbo oil cooler housing (at the engine)
1 piece oil pressure relief valve - for engines through '86

I also have several engines, disassembled. If you are looking for engine parts, I probably have them.

I also have body parts. Offhand, I know I have several doors, several front air dams, a few fenders etc.

For the stuff not pictured, I might need a few weeks to dig things out as I haven't gone through it in a while

Let me know if you have any questions about anything. 94472SL AT GMAIL DOT COM

I am very interested in the following group of items. Please let me know what type of package deal you can offer for the following
Take care
Brad
864-630-9751

Lindsey racing brake ducts for front rotors (the piece that bolts to the spindle)
Eibach 400 LB front springs with helper springs
Racer's Edge Camber Plates
Ground Control adjustable coil over spring perches (a few threads at the top are worn from the springs but they're above where I ever set the perch. Also missing one of the o-rings that goes between the strut and the threaded part)
Koni Yellow front with some strut caps and bump stops thrown in
Eibach 450 LB springs
Turbo oil cooler housing (at the engine)
1 piece oil pressure relief valve

Brad,

I'll post here and then give you a call a bit later.

I looked up some values new:

Brake ducts $90
Camber Plates $499
Ground Control coilover adapters w/ springs $250
Turbo oil housing (used) ~ $150
OPRV (used) ~ $100

Call it roughly $1000+ new value. How's $500 shipped (assuming Greenville area from your area code)?

I'll give you a call when I'm clear of some work meetings.

Thanks!

Thanks
Can you verify that the OPTV and oil housing will work with a 88 block

Also, there are a few other items that I indicated an interest
In
Are they still available as if so how much
Thanks
Brad

Yes, sorry to be unclear. I meant $500 for everything you asked for - I was just establishing a value with the big stuff.

I'll see if I can pull out the turbo filter housing and OPRV tonight to check P/N's against an '88. My block was an '86 and I think there were some changes at some point during the model run but I'm not sure.

I'll give you a call tomorrow with what I find - been swamped in meetings all day. You can email me at 94472SL @ gmail dot com so we don't have to post publicly. Thanks